收藏本站
IRADK10
The Command Buttons
The “RESET MICRO” button will reset the microproces-
sor when pressed, restarting the board after a fault
conditions. You may want to use this button to stop the
motor immediately when a dangerous situation occurs.
The “TURN ON” button will enable the inverter and set
the green LED diode ON (unless a fault is present).
The “REFRESH SCREEN” button is used for updating
the drive variables displayed on the screen.
The “EXIT” button is used to exit the GUI tool and go
back to the operating system.
5. GUI control panel screen
Below said field, at the bottom left, observe the slider with
the caption “Temperature limit (default 85)”. Using this slider
you may adjust the temperature threshold for the thermal
protection. A default value is 85 degrees Centigrade, but
you may change this value 1 . Figure 5 shows GUI control
screen.
The “GO CYCLE” will bring you to the next form, wherein
the drive cycle control may be adjusted, programmed,
started and stopped.
Observe the 5 sliders on the right side of the screen used
for adjusting:
? The drive acceleration constant.
? The drive frequency (i.e. speed) command expressed
in [Hz].
? The IGBT PWM frequency selection (5 kHz or 10 kHz).
? The IGBT inverter lockout time selection
(800ns or 1600 ns).
? The motor rated voltage and frequency selection.
All these sliders are in their default position at start.
Moving the appropriate slider handles into new position
will automatically activate the serial link and pass the new
parameter to the drive.
1
When using sliders for the parameter adjustment, bring the mouse pointer over the slider handle, press and hold the mouse button, move the handle observing small yellow-framed
numbers that will appear indicating the current slider handle position, place the handle precisely to the position wanted and release the mouse button. Carrying the slider handle
away from the range and releasing the mouse button there will have NO effect on the drive parameter change.
www.irf.com
6
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
IRADK31 DESIGN KIT 1/4 HP DC FOR IR31XX
IRAUDAMP1 KIT REFERENCE DESIGN W/IR2011S
IRAUDAMP4 KIT 2CH 120W HALF BRDG AUDIO AMP
IRCS2277S DEMO FOR 3-PHASE/380V MOTOR DRV
IRDC2085S-DF BOARD EVAL CONV DC BUS W/IRF6603
IRDC3038 KIT W/IRU3038 PWM CTRL DDR 14-PI
IRDC3039 BOARD EVAL CTRLR PWM W/IRU3039
IRDC3046 KIT W/IRU3046 DUAL PWM LDO CTRLR
相关代理商/技术参数
IRADK31 功能描述:电源管理IC开发工具 1/4 HP DC brushless Mtr using IR31xx RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
IRADK-S10UP60 制造商:International Rectifier 功能描述:
IRAE410 制造商:MURATA 制造商全称:Murata Manufacturing Co., Ltd. 功能描述:PYROELECTRIC INFRARED SENSORS IRA SERIES
IRA-E410 制造商:MURATA 制造商全称:Murata Manufacturing Co., Ltd. 功能描述:PYROELECTRIC INFRARED SENSORS IRA SERIES
IRA-E410QW1 制造商:Murata Manufacturing Co Ltd 功能描述:PYROELECTRIC INFRARED SENSOR - Bulk
IRA-E410S1 制造商:MURATA 制造商全称:Murata Manufacturing Co., Ltd. 功能描述:PYROELECTRIC INFRARED SENSORS IRA SERIES
IRA-E410ST1 制造商:MURATA 制造商全称:Murata Manufacturing Co., Ltd. 功能描述:PYROELECTRIC INFRARED SENSORS IRA SERIES
IRA-E420 制造商:MURATA 制造商全称:Murata Manufacturing Co., Ltd. 功能描述:Dual Type Pyroelectric Infrared Sensor